Ref-Wiki.com -

Technical information Industrial Hot-water baseboard heating

Hot water baseboard heating

Hydronic water heating system circulates the hot water in every room through a plinth panels. "Hy-dronic" is another term for forced hot water heating. Hot water gives up its heat energy through the use of fins attached to the pipe or channel, carrying hot water. Plinth panels installed at the outer perimeter of the house provide heat curtain that surrounds those who were inside. The radiant heat of the rays of the warm surfaces in premises. Growth currents convected warm air to block the drafts and cold. Wall stay warm and cold spots are eliminated.

The boiler provides water from 120 to 210 degrees Fahrenheit water is pumped through pipelines in a plinth. Today boilers very efficient and very small in size. Most of the rooms are the size of automatic washing machine; some are as small as suitcases and can hang on the wall, depending on the size of the house is heated.

The Circulation Pump

Booster pumps are used for circulating hot water through the pipes. These pumps are designed to handle a wide range of pumping equipment.
They vary in size from small pumps 5 gpm potential for those who can handle thousands of gallons per minute.

Piping Arrangement

There are two different piping arrangements used hydraulic system of hot water: series loop and single-pipe systems, which are used for zoning. In the territory controlled by a system of two circulating pumps are attached to a single boiler, individual thermostats are used to control the zones. Of course, there are other methods, but these two are one of the most often used for home heating. Plumbing requirements are minimal, usually employing copper pipe soldering connections.

One-pipe systems can be operated on any forced or gravity circulation. Care must be taken to design and install a system with a characteristic temperature decrease is found in heat units farthest from the boiler in mind. Design gravity circulation and one-pipe systems must be planned very carefully to allow for the heat load and the losses in the system. The advantage of one-pipe system lies in its ability to carry out one or two heat-emitting units will be shut down, without interfering with the flow of hot water for other devices. This is not the case, in series-a closed system, where the blocks are connected in series and is part of the supply line. The pipeline is changed, so that allows you to slice and the other will not. It is obvious that the loop-loop systems are cheaper, because it has very simple piping arrangement.

Hot Water for Other Purposes

You can use the boiler hydronic heating system for heat supply for purposes such as melting snow, swimming pool, water heating for household needs and for other purposes. Separate circuits are created for each of these goals, which are controlled by their own thermostats. Each of them is designed to merge into the main heating circuit from which it receives its supply of hot water. Hot water for household needs, for example, can be obtained using a heat exchanger or special coil inserted into the boiler. Please note that the water supply does not come in contact with water, heated by a boiler room for the server Board units and other purposes.

One of the drawbacks of the hydraulic system is its slow recovery. If the outside of the door is open in cold weather, at any time, it takes considerable time for the room to come back to a comfortable temperature. There is also the noise of pipelines of heating and expanding appear becomes rather annoying at night when you're in a quiet room and not too sleepy. The main advantage, however, is its efficiency. The type of fuel used determine the costs. Boilers can be electrically heated, natural gas heating, or heated oil...

 
Thanks ->

Air standard refrigeration cycle Deep evacuation Difference between quick and slow freezing External equalizer Hermetic motor High side low side refrigeration Hvac system working principle Internal and external thermostatic expansion valve Pan humidifier Refrigerator vacuum pump Technical data on net refrigerant effect Two stage refrigeration system Vapour compression refrigeration pressure enthalpy graph

Tools

Home
CONTACT
SELECTION CHILLER
BLOG
TOOLS

Menu

Chillers
Cold Store
Compressors
Compressor Packs
Heat Exchanger
Projects
Conversion Sizes
Refrigerant Chart
Technical Information
Calculate The Power Conditioner
Conversion
Chamber 60mm
Chamber 80mm
Chamber 100mm
Chamber 120mm
Shock freezing chamber
Copyright @ 2009 - 2013, "www.ref-wiki.com"